How To Use Two Wireless Routers In The Same House

Single- or Dual-Band?

Best Wireless Routers for 2018
Anyway, just wanted to say thank you! The ease with which you can switch between networks depends on the software on the device. It will be in hexadecimal numbers 0-f and will look something like this: Disconnect your laptop from the client router and re-enable wireless. If you want seamless switching "roaming" between the two ISPs, then give the networks the same name and security settings.

What You Need To Make Two Wireless Routers Work Together

The Best Wireless Routers of 2018

Read your manual to find out how to load its administration interface and then find the setting that lets you turn on client mode.

The client mode setup will prompt your for any necessary security information and then connect to your primary router. After the client router successfully connects, you need to change one more setting. Disconnect your laptop from the client router and re-enable wireless. The only catch is that you need to run an ethernet cord between the two locations. After you choose locations for your routers, connect your primary router to your Internet modem and configure its security settings.

Then plug one end of an ethernet cord into one of the regular LAN ports on your primary router and plug the other end into the uplink port on your client router. Then turn on your client router. In the next step you will need to access your routers IP address to change settings. After the client router boots up, disconnect your laptop from the wireless network and use ethernet cord to connect to the client router.

Log in to its administration interface consult your manual for instructions and make the following changes: Make sure you save your settings changes, give them a few moments to fully save, and then put them into effect by restarting your router—pull out its electrical cord, count to five, and plug it back in.

Then test your new two wireless routers and enjoy up to twice the coverage! Looking to replace your wireless router or buy your second or third? Make sure you check out Amazon. See more Networking tips. Harding is a Linux Professional Institute certified system administrator and freelance writer with over 10 years experience working with Linux.

Hi Scott this setup is simply setting up a repeater. Mentioning this bc the title is kind of cumbersome - you could say, "Setting up wireless access points as repeaters". By definition, repeating a wifi signal means a single SSID with multiple access points. Monday, September 13, 4: Joseph But it's not a repeater setup. The second router is not repeating the WiFi signal, it gets the connection from a hard wire. I've got the same setup at my house using Apple gear routers that do expect you to do this, making it a bit easier , and it differs greatly from the former repeater that I did have setup.

Google OpenID guy above describes setting up the spare router as a repeater, and the disadvantage of doing so half speed. Scott's setup has the advantage of full speed, and probably better reliability as I never had great luck with any kind of a repeater. If Scott wanted to shorten the title, he could use "roaming", but then it wouldn't be terribly obvious to any but the initiated. Monday, September 13, 7: I did the same a few months back and overall it works well.

This happens if one moves devices around the house, but naturally is ok if devices are relatively static. Hi Scott, you shouldn't need to unplug your existing router to configure the new one. If your laptop supports MDX and most do, unless it's really old you can plug directly into the router, configure your settings and once it's complete connect it to the main network.

Powering down your router really should be a last resort type of move. For me, it also handles the television and phone. Something like that definitely gets noticed. Also, what your doing is, I believe, called a wireless distribution system WDS. Monday, September 13, 8: Technically speaking your secondary "router" is not a router, but an access point.

It will route nothing, it just passes all packets from the Air to the Ethernet and back, regardless of the IP-Addresses or Networks used in them. It wouldn't even need an own IP-Address, that's only used to configure the device. Hmmm, now I'm wondering if we've hit upon a solution to "jamming" my neighbor's open Wifi so the kids don't jump on his to surf the net at night.

If I setup a spare router to have the same SSID as his and the same channel, my "fake" signal would be stronger and the kids would attach to it and not the neighbor's. I'm sure the kids would initially think the neighbor got a new router or something since the signal would be better.

So then I could send the iPod Touch requests to the big bit bucket in the sky, or better yet, let it get to the net and monitor what they do in the middle of the night. What I did was setup two Linksys routers using ddwrt custom firmware. Then I set the Verizon router to pass through from the fiber box directly to my primary Linksys router.

The benefit here is, that both Linksys routers are connectible wirelessly AND via wire, with only the primary dealing out IP addresses. It's a pain to setup, and annoying because the fiber box in the basement is tied to Mac Addresses, and kind of shuts off for an hour after a mac address cloning. It's hard to tell if you've done it correctly right away because of that. Another annoying issue is that every time the power is cycled on the Verizon router, or Verizon pushes down an update, I need to go back in to the web interface and re-enable the coax network.

The benefits are great though, the Linksys routers seem to be a lot more powerful, handling more connections and speed than the Verizon router. Also with the custom firmware, they support better throttling of certain protocols, and have a bunch of other features. Just my two pennies. It's a free wireless utility that shows you hotspots, signal strength, and channels for networks in range.

Some of your signal strength issues could be from interference from neighbor's Wi-Fi, it's really easy to identify what channel you should use. It gives you a real-time graph similar to your Wikipedia graphic showing what channel each access point is on.

It's been a lifesaver at my house where we have a dozen Wi-Fi networks in range. With WDS or a repeater the second access point is basically receiving the WiFi signal from the main router and retransmitting it on a different channel. In Scott's solution he is taking a router and tricking it into acting like an Access Point, so the backhaul to the rest of the network is wired not wireless. That is a much better solution as you are effectively doubling your total WiFi bandwidth.

You can eliminate about half the steps if you just use an Access Point instead of a router, but if you already have a router sitting around then disabling DHCP is an easy trick to save you from having to buy yet another device. Scott I set up a Wireless Distribution System WDS about a year ago using two Linksys routers one downstairs and one upstairs and it has been working flawlessly ever since.

I simply added a range extender to support wireless access in a 3 floors house. However I am thinking about doubling them with wireless routers that do NOT hand out ip addresses but add extra security protocols: Monday, September 13, 5: However, as you point out, folks have piles of standard routers lying around their houses, as I did, so it's a reasonable solution.

I updated the post, just to be clear. This is not a repeater, it's a second AP plug directly into the first's hub. Sveasoft released Alchemy v6. It runs the phone and TV at my house also, but I just asked folks, gave them a heads up and rebooted. Still, it IS a valid alternative as you rightly point out.

RHertzler - Only if you know your neighbor's wifi security password. Monday, September 13, 9: You'll get an IP no matter which AP your wireless associates with. I did this years ago I guess as you get older you loose your hearing range. I am surprised you use DHCP for everything. I have my DHCP set to start at. The two WiFi are also simultaneously ON and still they work very well and data doesn't get mixed up or tangled in any way.

Also, I would like to add up that if the connection from one ISP cannot be established, then the Laptop will try to connect to the other available ISP. So, If you are trying to enhance availability of your internet connection then yes, it will help you. However, this switching time is of a few seconds to minutes.

Some real-time applications may get affected or may disconnect in the switching time delay. However, I am not sure if there are any programs available for quick switching from one ISP to another. Lets say you connect to the Hathway ISP connection. Now, your iPad will search for Available Wireless Networks.

So, as you can see, both Laptop and iPad are independent of each other. Even if one device is connected to an ISP's connection, multiple other devices can still connect to the same connection. However, this will disconnect you from the previously connected ISP's Network connection. Yes, but you may have to change the wiring setup in your house a bit to make it work. For example, on the outside of my house there is a splitter with a single input and multiple outputs.

The line from the ISP connects to the input port, while the output ports are connected to the various cable drops inside the house. With this setup I cannot use two ISPs at the same time, as there is only one input. With two ISPs you will obviously have two input lines, so you will have to find a way to get some of the drops inside the house connected to the first input line, and some of the ports connected to the second input line.

This may be easy or hard depending on your existing setup for example, the splitter may be inside the wall or in a hard-to-reach place. As for setting up WiFi to switch, that part is easy - you would just need to connect one router to a cable drop served by the first ISP, another router to a cable drop served by the second ISP. If you want seamless switching "roaming" between the two ISPs, then give the networks the same name and security settings.

If you don't want it to switch automatically, then just give the networks different names and then you can select the network manually. By clicking "Post Your Answer", you acknowledge that you have read our updated terms of service , privacy policy and cookie policy , and that your continued use of the website is subject to these policies. Home Questions Tags Users Unanswered.

Your Answer

Leave a Reply

Yes, it is possible to utilize two (or even more than two) routers on the same home network. The benefits of a two-router network include: The benefits of a two-router network include: Support for more wired devices: If your first router is the wired Ethernet kind, it supports only a limited number of connected devices (typically only four or five). Hello all, ill be brief on this one. So my house is a two story house, my computer room is where my modem, wireless router, and file server are located. My entire house networking system is based. How To Use Two Wireless Routers In The Same House March 23, by David If you have a big house (or office), you may find it necessary to run two wireless routers (or more) to share the internet connection around efficiently.